Wika IPT-11 Uživatelský manuál Strana 1

Procházejte online nebo si stáhněte Uživatelský manuál pro Měřící nástroje Wika IPT-11. WIKA IPT-11 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - Operating Instructions

Operating InstructionsIndicating and adjustment module for IPT-1* sensors

Strany 2 - Contents

Dismounting is carried out in reverse order.10 Indicating and adjustment module for IPT-1* sensors4 Mounting31549-EN-081211

Strany 3 - 1 About this document

5 Set up5.1 Adjustment system1.1231Fig. 4: Indicating and adjustment elements1 LC display2 Indication of the menu item number3 Adjustment keysl [OK] k

Strany 4 - 2 For your safety

5.2 General functionsIPT-1* pressure transmitters have various functions. Hence they canbe adapted to the respective application.Some of these functio

Strany 5

The linearization curve creates a correlation between height andvolume. It takes into account the vessel geometry for the displayedmeasured value and

Strany 6 - 3 Product description

l Min. and max. temperature2)PointerIn this menu item, the device status is displayed. If the sensor detectsa fault, "OK" will be displayed.

Strany 7 - 3.3 Operation

1 Push [OK]2 Select the requested simulation variable with [->] and confirm with[OK]3 Set the requested value with [+] and [->].4 Push [OK]The si

Strany 8

The sensor is already set to the ordered national language. In thismenu item you can change the language. The following languages areavailable, e.g. i

Strany 9 - 4 Mounting

In this menu item, the PIN is activated/deactivated permanently.Entering a 4-digit PIN protects the sensor data against unauthorizedaccess and uninten

Strany 10 - 31549-EN-081211

l Sensor details, e.g. approval, process fitting, seal, measuring cell,measuring range, electronics, housing, cable entry, plug, cablelength etc.Sensor

Strany 11 - - Select editing position

Display unitVolumelScaling0 % = 0.0 l100 % = 100.0 lMenu section, serviceIn the menu item "Current output" you determine the behaviour of th

Strany 12 - 5.2 General functions

Contents1 About this document1.1 Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31.2 Target group . . . . . . . . . . . .

Strany 13

l In the menu item "Failure mode" under "Current output", theparameters "Hold value" and "20.5 mA" are blocked

Strany 14

The channel is the input selector switch for function block (FB) of thesensor. Within the function block, additional scalings (Out-Scale) arecarried o

Strany 15

Here, you determine the unit and scaling for PA-Out. These settingsalso apply to the values displayed on the indicating and adjustmentmodule if in the

Strany 16

5.5 Menu schematicInformation:Depending on the version and application, the highlighted menuwindows are not always available.Basic adjustment1▶Basic a

Strany 17

Diagnostics3Basic adjustmentDisplay▶DiagnosticsServiceInfo3.1Pointerp-min.: -5.8 mbarp-max.: 167.5 mbarT-min.: -12.5 °CT-max.: +85.5 °C3.2Sensor statu

Strany 18

Indicating and adjustment module for IPT-1* sensors 255 Set up31549-EN-081211

Strany 19

5.6 Menu schematicInformation:Depending on the version and application, the highlighted menuwindows are not always available.Basic adjustment1▶Basic a

Strany 20

Service4Basic adjustmentDisplayDiagnostics▶ServiceInfo4.1Additional PA valueSecondary Value 14.2Out-Scale-UnitVolumel4.3PA-Out-Scale100.00 lin %= 0.0

Strany 21 - - Linearised percentage value

5.7 Menu schematicInformation:Depending on the version and application, the highlighted menuwindows are not always available.Basic adjustment1▶Basic a

Strany 22

Service4Basic adjustmentDisplayDiagnostics▶ServiceInfo4.2SimulationStart simulation▼4.3ResetSelect reset▼4.3LanguageDeutsch4.4Copy sensor dataCopy sen

Strany 23 - 5.5 Menu schematic

1 About this document1.1 FunctionThis operating instructions manual provides all the information youneed for mounting, connection and setup as well as

Strany 24

6 Maintenance and fault rectification6.1 MaintenanceWhen used in the correct way, no special maintenance is required innormal operation.6.2 Instrument

Strany 25

7 Dismounting7.1 Dismounting stepsWarning:Before dismounting, be aware of dangerous process conditions suchas e.g. pr essure in t he vessel, high temp

Strany 26 - 5.6 Menu schematic

8 Supplement8.1 Technical dataGeneral dataWeight approx. 150 g (0.33 lbs)Ambient conditionsAmbient temperature -15 … +70 °C (+5 … +158 °F)Storage and

Strany 27

8.2 DimensionsIndicating and adjustment module27,6mm(1 3/32")ø66,3mm(2 39/64")45,1mm (1 25/32")9,7mm (3/8")Fig. 5: Indicating and

Strany 28 - 5.7 Menu schematic

34 Indicating and adjustment module for IPT-1* sensors8 Supplement31549-EN-081211

Strany 29

Indicating and adjustment module for IPT-1* sensors 358 Supplement31549-EN-081211

Strany 30 - 6.2 Instrument repair

WIKA Alexander Wiegand GmbH & Co. KGAlexander-Wiegand-Straße 3063911 Klingenberg/GermanyPhone +49 9372 132295Fax +49 9372 132706e-mail: support-tr

Strany 31 - 7 Dismounting

2 For your safety2.1 Authorised personnelAll operations described in this operating instructions manual must becarried out only by trained specialist

Strany 32 - 8 Supplement

2.7 Compatibility according to NAMUR NE 53With respect to compatibility, NAMUR recommendation NE 53 is met.The parameter adjustment of the basic senso

Strany 33 - 8.2 Dimensions

3 Product description3.1 ConfigurationThe scope of delivery encompasses:l Indicating and adjustment modulel Documentation- this operating instructions

Strany 34

12Fig. 2: Rear of the indicating/adjustment module1 Integrated seal ring2 Gold plated contact paths3.2 Principle of operationThe indicating and adjust

Strany 35

3.4 Packaging, transport and storageYour instrument was protected by packaging during transport. Itscapacity to handle normal loads during transport i

Strany 36

4 Mounting4.1 Mounting stepsThe indicating and adjustment module can be inserted or removed atany time. It is not necessary to interrupt the voltage s

Příbuzné modely IPT-10

Komentáře k této Příručce

Žádné komentáře